logo

toilet anchor bolts sizes

Toilet Holddown Bolt Spins. - Forum - Bob Vila

Went to install a new toilet on this tile job and one of the bolts in the flange was spining. The other one held fine. Went and got a 5/16 bolt, but t...

The two bolts that bolt a toilet to the ground require what ...

Sep 16, 2007 · The two bolts that bolt a toilet to the ground require ... The two bolts that bolt a toilet to the ground require what size ... My toilet flushes ...

Toilet Flange Bolts Spinning In Place - Plumbing - DIY Home ...

toilet flange bolts spinning in place. ... (There should be a law stating that all toilet bolts, nuts and washers shall be stainless steel only, ...

Toilet Buying Guide - Lowe's Home Improvement

Toilet Buying Guide. ... in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the ...

How do I properly size toilet tank bolts? |

Most toilets use standard sized toilet tank bolts. Skip to Navigation. Skip to Content. Cancel. Search. How-Tos ... How do I properly size toilet tank bolts?

Kitchen & Bathroom Repairs : How to Install Hold-Down Bolts ...

Jan 25, 2012 · The hold-down bolts on a toilet prevent damage to the toilet and damage to the plumbing by holding it steady. Bolt down your toilet with the help of a profes...

Wax Ring and Bolts for Toilet Bowl-D6033-40 - The Home Depot

Nothing specifies solid brass anchor bolts. ... for the wax ring and bolts for toilet ... not use this ring and bolts assy, as the bolts were 1/4-inch size, ...

4 Tips for Replacing Toilet Flange Bolts |

Before you begin, measure the distance from the wall behind the toilet to the toilet flange bolts. This measurement is called a "rough in," and most toilets were made with a 12-inch rough in. If your rough in is a different size, ask your local toilet store for assistance. Once you are done with ...

Concrete Fasteners | CONFAST

Product listing of concrete fasteners, concrete anchor/fasteners ... (the sizes always refer to the inside diameter of the anchor, i.e. the size of the bolt to be ...

Toilet/Closet Flanges - New, Replacement and Repair

Select from a variety of new and replacement toilet flanges. ... bolts and washers; Choices include flanges for ... the toilet flange dimensions refer to the ...

Shop Anchor Bolts at - Hardware Store

Shop anchor bolts in the bolts section of . Find quality anchor bolts online or in store.

Size of toilet bowl hold down bolts -

Size of toilet bowl hold down bolts; Author: criecke Are the hold down bolts all the same size on all toilets ? I got a pair at the local hardware store but

Next by Danco Zero Cut Bolts Toilet Mounting Bolts, Brass ...

Next by Danco Zero Cut Bolts Toilet Mounting Bolts, ... Product Dimensions 3 x 0.4 x 0 ... long bolts, anchor bolts, Best Rated in Toilet Mounting Parts, ...

Plastic Toilet Bolts? - Plumbing - DIY Home Improvement ...

I just had a plumber over to replace a plastic toilet bolt that snapped when I tried to tighten it. He was incredulous that another plumber would use plastic bolts.

How to Replace Toilet Anchor Bolts | Home Guides | SF Gate

Toilet anchor bolts hold your toilet to the floor and keep it connected to the flange, which is the opening to the waste line. Moisture around the base of the toilet can corrode the anchor bolts.

Toilet Tank Bolt Sizes? | Yahoo Answers

Aug 28, 2009 · Toilet Tank Bolt Sizes? ... can I use the slightly narrower brass bolts that came with the kit or do I need the exact size for my toilet tank?

Replacement Toilet Bowl Bolt Caps and Tops in many colors

Toilet Bowl Bolt Caps and Tops ... Fits the two most common sizes of metal bolts used in ... "Will these toilet bowl bolt caps colors match my toilet ...

Replacing Toilet Anchor Bolts | Toilets | Plumbing | Repair ...

Replacing toilet anchor bolts is necessary when the bolts are rusted. Any time you take the toilet up, you should replace them as a maintenance activity.

What is the proper procedure for replacing rusted toilet ...

I have a 1.6 gallon American Standard toilet that rocks a little from side to side. Upon closer examination, it looks like at least 1 (or both) of the anchor bolts are loose (they had corroded mat...